Author Topic: Tap for M8 bolt  (Read 2758 times)

Mike dubs

  • Malibu Status
  • **
  • Posts: 71
    • View Profile
Tap for M8 bolt
« on: March 02, 2022, 12:44:48 AM »
Guys,
I trimmed a spare alloy axis mast down and need to tap the holes for the old M8 bolts.

There are different taps and it's confusing for the non mechanically minded, what tap do I need?

Cheers

Mike

JonathanC

  • Peahi Status
  • *****
  • Posts: 678
    • View Profile
Re: Tap for M8 bolt
« Reply #1 on: March 02, 2022, 02:25:04 AM »
It’s a standard M8 x 1.25 bolt. Just use a regular tapered tap. Most important thing of course is to get it all straight.
Good idea to use some sort of cutting fluid and wind in then back out then cut a bit more etc etc.
« Last Edit: March 02, 2022, 02:31:42 AM by JonathanC »

Geoff C

  • Rincon Status
  • ***
  • Posts: 149
    • View Profile
Re: Tap for M8 bolt
« Reply #2 on: March 02, 2022, 02:36:01 AM »
Here you go.
Bottoming chamfer is the best to use.

https://www.mcmaster.com/8305A59/
Geoff C.

Mike dubs

  • Malibu Status
  • **
  • Posts: 71
    • View Profile
Re: Tap for M8 bolt
« Reply #3 on: March 02, 2022, 02:59:46 AM »
Great thanks guys.

Mike

PonoBill

  • Cortez Bank Status
  • *****
  • Posts: 25871
    • View Profile
Re: Tap for M8 bolt
« Reply #4 on: March 02, 2022, 08:57:09 AM »
Actually, Geoff, since the mast holes go all the way through the mast there's no need for a bottoming tap. a regular tap will be easier to start and will dump chips better. Like Jonathon says, use cutting oil--the cutting oil for aluminum does the best job but who the hell has that (well, actually, me) but if you sneak into the kitchen and swipe a dab of your wife's coconut oil you be fine. Don't get bored with the process and just wind the tap in, your threads will be weak. The process is half a turn in, full turn out then run it in until it starts to cut and do another half turn, then full turn out. It's bitchy, but that breaks the chips off and releases them, giving you smooth, full-depth threads.
Foote 10'4X34", SIC 17.5 V1 hollow and an EPS one in Hood River. Foote 9'0" x 31", L41 8'8", 18' Speedboard, etc. etc.

Mike dubs

  • Malibu Status
  • **
  • Posts: 71
    • View Profile
Re: Tap for M8 bolt
« Reply #5 on: March 06, 2022, 11:35:55 PM »
Thanks guys  worked a treat, tapping was easy with your advice.
I now have a 75cm to go with my longer cedrus. Mike

 


* Recent Posts

post Re: Sunova Ghost 8'10 SUP
[Classifieds]
kliss99
Today at 05:01:39 AM
post Re: Need a new Impact Vest
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
PonoBill
April 23, 2024, 07:55:28 PM
post Re: Need a new Impact Vest
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
B-Walnut
April 23, 2024, 07:26:43 PM
post Re: Need a new Impact Vest
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
spindrift
April 23, 2024, 07:16:46 PM
post Re: Need a new Impact Vest
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
B-Walnut
April 23, 2024, 06:56:28 PM
post Need a new Impact Vest
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
spindrift
April 23, 2024, 06:36:51 PM
post Re: Ocean Rodeo Glide-Allula
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
kiteboarder
April 23, 2024, 06:06:50 PM
post Re: Ocean Rodeo Glide-Allula
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
B-Walnut
April 23, 2024, 04:22:52 PM
post Re: Ocean Rodeo Glide-Allula
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
kiteboarder
April 23, 2024, 03:07:49 PM
post Re: Ocean Rodeo Glide-Allula
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
B-Walnut
April 23, 2024, 02:59:32 PM
post Re: Ocean Rodeo Glide-Allula
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
Dwight (DW)
April 23, 2024, 02:41:07 PM
post Re: Erik Antonson interview with Stacy Peralta
[Random]
surfinJ
April 23, 2024, 01:34:42 PM
post Fanatic 8.3 Allwave
[Classifieds]
firesurf
April 23, 2024, 01:28:40 PM
post Re: Ocean Rodeo Glide-Allula
[Wingsurfing, Windfoiling, Wingfoiling, Wing SUP]
B-Walnut
April 23, 2024, 01:24:35 PM
post Re: At what age did you, or do you plan to retire?
[Random]
surfinJ
April 23, 2024, 01:24:13 PM
SimplePortal 2.3.7 © 2008-2024, SimplePortal