Messages

1

Foil SUP / Re: Axis Modulus vs High Modulus Mast

« on: July 06, 2023, 08:05:16 AM »

Little update for you all. The high modulus made the shaking go away, just sucks that it cost $1500.

2

Classifieds / Axis 910 $450 shipped.

« on: July 02, 2023, 06:55:43 PM »

Axis 910, light wear. Leading edge is smooth. Has a few light scratches. $450

3

Foil SUP / Re: Axis Modulus vs High Modulus Mast

« on: June 22, 2023, 07:05:07 AM »

when I get into a good wave or a certain speed with the 1300 it feels like the whole entire board and foil have speed wobbles. It's actually terrible. Wondering if its the mast wiggling or me being a bad foiler. Couple of other people have tried my setup and noticed the wobble immediately.

4

Foil SUP / Re: Axis Modulus vs High Modulus Mast

« on: June 21, 2023, 06:45:19 AM »

1300 is my biggest right now

5

Foil SUP / Axis Modulus vs High Modulus Mast

« on: June 20, 2023, 03:56:04 PM »

Any reason why I need to spend the extra $300 for a high modulus mast vs the modulus mast? I weight 170 lbs and tow, wing, DW, SUP, and prone foil.

6

Wingsurfing, Windfoiling, Wingfoiling, Wing SUP / Re: Narrow vs Wide Boards: Beginners to Advanced

« on: June 19, 2023, 11:52:59 AM »

What would you guys recommend for someone who has a barracuda and a larger board at their disposal. Have lots of foil experience via efoil, tow boogie, and sup foil but hardly any experience riding switch and wing. Wanting to get into winging.

7

Foil SUP / Re: SUP vs hand paddles on barracuda style boards?

« on: May 08, 2023, 06:44:56 AM »

My thinking would be if you wanted to prone you'll want the extra glide of the longer bigger board. Similar how to a 9' glides vs 12', the 12' seems to glide much better.

8

Foil SUP / Re: Balancing on Barricuda Style Boards

« on: April 11, 2023, 10:17:26 AM »

First session on the barracuda this past weekend, I think I stood for a total of 5 seconds and being in the water for an hour. I'm not shy to supping, normal sup board is a 7'2"x29" Kazuma. These things have a steep learning curve.

What size Barracuda and what size foil?

7'10"x19", 105 L, Axis 1300

9

Foil SUP / Re: Balancing on Barricuda Style Boards

« on: April 10, 2023, 08:39:20 AM »

First session on the barracuda this past weekend, I think I stood for a total of 5 seconds and being in the water for an hour. I'm not shy to supping, normal sup board is a 7'2"x29" Kazuma. These things have a steep learning curve.

10

Wingsurfing, Windfoiling, Wingfoiling, Wing SUP / Re: Axis PNG 1300 for light wind?

« on: January 23, 2023, 07:05:28 AM »

I'm Able to stay on foil at 6mph with my Axis 1300 weighing in at 165lbs in super light wind.

11

Wingsurfing, Windfoiling, Wingfoiling, Wing SUP / Re: Cutting down a 90cm Axis Alu mast AND potting a carbon mast head

« on: October 28, 2022, 07:09:12 AM »

Little Update: I cut the mast down to 30" and the holes were drilled but not threaded. I used a fine tooth new blade on my chop saw and went very slow. It cut very clean and square. Took a small file to the interior and exterior edges to clean up any burrs and there were very few. Tapped the holes with a 8x1.25 tap and fluid. Once that was done I used caulk from the hardware store to seal up the main cavity as I hate how water just sits in there when I am done riding.

Hope this helps.

12

Wingsurfing, Windfoiling, Wingfoiling, Wing SUP / Re: Cutting down a 90cm Axis Alu mast AND potting a carbon mast head

« on: October 27, 2022, 10:16:53 AM »

I am attempting this tonight....wish me luck. From what I have found online, the holes are drilled but not threaded all the way through. The mast's are fairly cheap so I am not afraid of ruining it for this project.

13

Classifieds / Re: Foil Drive Assist $1050 in Southern Cali(OC)

« on: September 26, 2022, 08:06:00 AM »

messaged.