Thanks for your feedback!
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - Fanman
Pages:  2
I am gonna be using a room in my basement. I'm looking for opinions and experiences using Epoxy. How much venting will I need, or is it a required with Bio Resigns or is a respirator enough? Resin Research vs. Entrophy Super Sap, or ?
Thanks for your feedback!
« on: December 26, 2016, 07:09:07 PM »
If any locals want to surf, surfsup let me know?
Going to be in Gizzy, Whangamata, Hawkes Bay, Manguwai, and Ahipara, with stops along the way. Repeat from last year with a few modifications.
« on: December 05, 2016, 04:25:49 PM »
Rail saver Pro is installed. Very lightly used can be ridden as a thruster, quad or five fin. 6oz. Bottom, carbon stringer, vector net. Top is 6oz + 4oz. And 4oz in standing area. All S-Glass. Fun and fast and light!
You can try 1st in So Cal!
I've got a couple buns in the oven. One for my wife, Mango Tango as she calls it.
8'6"x31"x 128L she likes to be comfortable but ride my shorter ones too!
My 8'2" x 30.5"x 118L
Trying out the new vertical carbon deck material with a hexagon patch and on bottom of the boards! Huey will be ready to ride Tuesday!
I am in NY. Until the 2nd of Dec. then heading out to Cali. This board in So Cal and ridden only once. I have a similar board to this one, so I figured I'd sell it rather than have it remain resting. The board is glassed 7.5 oz bottom 7.5/6oz. Deck plus Vector net and 4oz. Patch in the standing area. 1.5# stringerless blank. It has a acrilic gloss coat. It also has Rail Saver Pro on the rails. So it's good to go! I can meet you in So Call with the board after the 2nd and you can try it 1st also.
I'll accept a reasonable offer for the board a head of time, so give me a shout if you are interested?
I was surfing yesterday 2-3' sand bar peaks and had a little snafu. Late drop wipe out and snap. I jumped back aboard and my paddle blade was in two pieces. Not quite sure hat did it?
Any other guys had similar issues? I was bummed, but did have a back up for the next session. Same paddle blade re-glued and back in action.
« on: June 25, 2016, 04:32:28 PM »
I've got 2 nice condition custom boards ready to sell. I've got other boards I have been riding, so I'm selling these boards made by Ed Angulo and glassed in the Cannibal CorVac facility if FL. the 7'10" is a Fish tail 30.5 x 115L and the 8'4" x 31" x 122L Swallow tail, both boards are very light and strong. I will be happy to send picks and more info to anyone interested and possibly trade for another board, flat water of HP SurfSUP. I've got boxes and can ship with Pilot Air or others?
Please no super low balls etc.
New Zealand has been a blast!
My wife and I are going on are 4th week in NZ.
We have surfed in Tairua, Whangamata, Gizborne at multiple spots, Raglan, Ahipara and Ninety Mile Beach. I haven't been able to post picks as it says they are to large, but I have gotten tons of picks. It truly is land of the lefts. Other than a right point break near Gisborne we have surfed mostly all lefts!
I've got picks on my Instagram if any one is interested in seeing some nice waves in NZ.
Fun waves the last couple mornings and it is suppose to continue!
I had a chance to get my new 7'10" in some fun and fast waves. The water is 71 and air was 63, but with the sunshine I was nice and toasty. The crowd was minimal, I got out at 8:30 and still just a hand full of guys spread out nicely
My wife and I were thinking Costa Rica, but New Zealand has been on my bucket list for a long time and needed to be crossed off 1st.
We are heading there mid Feb - mid March. So far we booked the last week at Ahipara in the Northland. We are open to some suggestions for areas with some SUP friendly surfing!
Pages:  2